Our standard 700 Series – the heart of Ever-Power swiftness reducer products – has been serving industry reliably for over a decade. Its proven modular design has set the industry standard for efficiency and may be the most imitated product in the current worm gear speed reducer marketplace. But why accept a knock-off when you can have the original – from Ever-Power.
Specifications
11 basic solitary reduction sizes
8 basic double reduction sizes
1/6 – 25 HP
5:1 – 100:1 ratios single reduction
100:1 – 3600:1 ratios double reduction
Non-flanged, NEMA C-face quill, and coupled input styles
Projecting and hollow result shafts
Projecting diameters from 1/2″ to 2-1/4″
Hollow output bore diameters from 5/8″ to 3-7/16″ (with over 20 bore sizes in stock)
Product Features
The 700 Series’ large oil reservoir provides efficient heat dissipation and lubrication for longer operating lifestyle.
Its multi-position mounting flexibility allows for installation in virtually any position.
Housings are straddle-milled, top and bottom level, for precise alignment of horizontal and vertical bases.
Internal baffles assure positive, leak-free venting.
The 700 Series’ rugged housing, fabricated of fine-grained, gear-quality cast iron, provides optimum strength for maximum durability, in addition to greater precision during worm and gear alignment.
Ever-Power 700 Series high-strength bronze worm equipment is straddle mounted between heavy-duty tapered roller bearings to increase thrust and overhung load capacities, sizes 713-760.
Our 700 Series’ high-strength steel output shaft assures convenience of high torque and overhung loads.
Pipe plugs allow easy fill, level, and drain in any mounting position.
The 700 Series’ super-finished oil-seal diameters on both input and output shafts extend seal lifestyle.
Both 2D and 3D CAD drawings can be found in our eCatalog.
Ever-Power worm gearboxes have earned a status to be an industry benchmark worldwide. Our success originated from our relentless drive for quality with state-of-the-artwork technology, all and will be offering worm gearboxes are inexpensive prices. High flexibility accorded through a wide choice of mounting options, shaft configurations and motor interfaces, makes the Ever-Power worm gearbox the default choice for the sector. The helical-worm and the double-worm version, with or without the torque limiter, soon add up to the advantage, creating a highly versatile drive system.
Ever-Power Worm gearboxes provide high torque with low swiftness gear ratio. Being basic and compact in design, these gears can perform higher gear ratio than the helical gears. These worm decrease gears having screw type characteristics are similar to helical gears, but its helix angle is typically comparatively bigger) and its body is generally quite lengthy in the axial direction. The gears in these gearboxes can be correct or left-handed dependant on the purpose.
Mounting choice include universal housing, aspect flanges, foot (horizontal and vertical), shaft mounted with torque arm. Available in Solid shafts (single or double), with torque arm or torque limiter.
Worm reduction gears features
Principles
A worm gear is a kind of interlocking gear made up of a worm shaft and worm wheel. The worm is certainly shaped such as a screw and the worm wheel is certainly a type of gear machined to possess a tooth profile with the same configuration.
The procedure of a worm gear is similar with that of a bolt and nut. The principle is the same as a nut that has been fixed to ensure that it cannot rotate and for that reason progresses in the axial path when the bolt can be turned.
The design of a worm gear is thought of through the relationship between the rack and spur gear on the middle plane of the worm wheel.
Features
High reduction ratio One rotation of the worm rotates the worm wheel simply by one tooth. For this reason, in a 1 speed reduction gears, the wheel could be manufactured therefore that it will be rotated 1/60 (1/120 in particular applications).
Orthogonal shaft The shafts are aligned orthogonally due to the structure. This feature makes it possible to layout the turning tranny direction at the right angle.
The arbitrariness of the rotation direction The screw direction of the worm can be clockwise or counterclockwise (generally clockwise). It is possible to Worm Reducer change the rotation path of the worm wheel by changing the screw direction.
A multitude of shaft layouts The wide variety of shaft layouts is among the features of interlocking gears.For example, right shaft output, still left shaft output, dual shaft input and dual shaft output, etc., combine for a complete of 14 types (Figure 2) and, if attachment orientations are included, you’ll be able to select from over 40 layouts.
Low noise, low vibration The interlocking of the worm and worm wheel is certainly characteristic because the contact is linear and the relative slide is great. In comparison with rolling power transmission, sound and vibration are really low. For this reason, this technology is used to drive medical gear, elevators and escalators, etc.
The principal specifications of worm reduction gears
MA Series(Small)
Center distance(mm) 32,40
Reduction ratio 10,20,30,40,50,60
Input capacity(kW) 0.1~1(at an input of 1800 rpm)
Output torque(N・m) 20~66
Input speed(rpm) 0~1800
MA Series(Medium)
Center distance(mm) 50,63,80,100,125,140,160
Reduction ratio 10,15,20,25,30,40,50,60
Input capacity(kW) 0.4~30(at an input of 1800 rpm)
Output torque(N・m) 900~3570
Input speed(rpm) 0~1800
S Series
Center distance(mm) 50,60,70,80,100,120,135,155,175,200,225,250,300,350,400,450,500
Reduction ratio 10,15,20,25,30,40,50,60
Input capacity(kW) 0.3~255(at an input of 1800 rpm)
Output torque(N・m) 50~56600
Input speed(rpm) 0~1800
Key points when choosing a worm reduction gears
Selection
When selecting a worm reduction gears, the procedures for selecting the correct gear are described in the maker catalogs and the series and models should be selected according to those procedures. Particular care should be taken in crucial areas such as selecting the strain index, calculating the overhang load and examining heat rated capability from the manufacturer.
Cautions during use
When utilizing a worm decrease gears, heat produced through the initial period of make use of is high and running-in operation at 1/4, 1/2 and 3/4 of rated torque for eight hour periods is paramount to sufficiently attaining the performance of the worm reduction gears.
Maintenance and inspection
After completing running-in procedure (approximately 50 hours), it’s important to improve the lubricating oil and to change the lubricating oil from then on about 1 time per year according to the operation manual supplied by the manufacturer.
Product Description
The Worm Decrease Gear Box is provided by our company is of high-quality. Our products are created by using premium quality material and progress technology at our vendors end. They are widely used in a variety of sectors. Our items are easily available at a very low market prices.
Motor Mount Frame Options
TEC Motors, worm decrease gearbox.
Option A-160 B5 Frame, Flange Mount.
Choice B-132 B14 Frame, Face Mount.
Option C-100/112 B5 Frame, Flange Mount.
High efficiency and secure operation. High load capability and overload functions. Output Torque = (Power (kW) x 9550 (Constant))/ Gearbox result speed (rpm).
Higher ratios on request reliant on service factor (40:1, 50:1, 60:1, 80:1, 100:1)
DESCRIPTION
Wormgears of the VF series are milestones for the industry worldwide. They succeeded in combining uncompromising quality with stateoftheart technology amd renown cost effectiveness.Absolute flexibility is given by the wide selection of several mounting options, shaft configurations and engine interface, all offered as regular. The helicalworm and the doubleworm version, with or without the torque limiter, also add up, creating a highly versatile drive system.
ADDITIONAL INFORMATION
AMP
0.42 A
EFFICIENCY
84%
HP
0.12
KW
0.09
RATIO
7
RPM
200
TEMPERATURE RATING
20 level C TO 80 degree C
TORQUE
4 Nm
HSN
8483.40.00
WARRANTY PERIOD
12 Months
The worm reduction gears can be found in two series: X and H.
The series X, featuring a worm and worm wheel set, comes in versions XA with shaft and XF-XC with mounting provisions for motor.
Version XF (bell housing + coupling) offers great versatility to match a broad selection of applications and higher efficiency than the compact line XC, where the emphasis is on space efficiency.
Series H offers the same features since series X with an extra plus: a spur equipment pre-stage at the insight end provides higher performance and a broader selection of ratios than the X series.
Frame sizes 110 and 90 feature a cast-iron housing cast enbloc, whereas smaller sizes make use of die-cast aluminium housings. The worm shaft is manufactured from casehardened and hardened alloy metal and ground-finished.
The worm wheel has a cast iron hub with cast bronze insert. Hollow output shaft is supplied as standard.
Broad range of options available:
second input, output flange, single or double extension output shaft, torque limiter with through cable, torque arm.